- 您现在的位置：买卖IC网 > Sheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
Table 13. Software Configuration Register
DATA BITS
D15*
D[14:12]*
BIT NAME
T2AVGCTL
T2LIMIT[2:0]
RESET STATE
0
000
FUNCTION
Channel 2 averaging-equation bit. This bit controls the averaging equation
for channel 2 while the device is in tracking mode. See Table 13a.
Channel 2 difference-limiter bits. Set T2LIMIT[2:0] to enable the difference
limiter for channel 2 temperature averaging. See Table 13b.
Channel 2 LDAC control bit. Set to 0 to load calculation results into the DAC
D11
LDAC2
0
2 input and output registers. Set to 1 to load calculation results into the
DAC 2 input register only.
D10
TCOMP2
0
Channel 2 temperature compensation enable bit. Set to 1 to allow V GATE2
calculations to be triggered by channel 2 temperature measurements.
Channel 2 APC parameter compensation enable bit. Set to 1 to allow
D9
APCCOMP2
0
V GATE2 calculations to be triggered by channel 2 current-sense
measurements or APC2 parameter changes.
Channel 2 temperature sensor select bit. Set to 0 to use the channel 2
D8
TSRC2
0
external temperature sensor as the source of the temperature parameter for
V GATE2 calculations. Set to 1 to use the internal temperature sensor.
D[7:6]
APCSRC2[1:0]
00
Channel 2 APC parameter select bits. Set APCSRC2[1:0] to select the data
source for V GATE2 calculations. See Table 13c.
Channel 1 LDAC control bit. Set to 0 to load calculation results into the DAC
D5
LDAC1
0
1 input and output registers. Set to 1 to load calculation results into the
DAC 1 input register only.
D4
TCOMP1
0
Channel 1 temperature compensation enable bit. Set to 1 to allow V GATE1
calculations to be triggered by channel 1 temperature measurements.
Channel 1 APC parameter compensation enable bit. Set to 1 to allow
D3
APCCOMP1
0
V GATE1 calculations to be triggered by channel 1 current-sense
measurements or APC1 parameter changes.
Channel 1 temperature sensor select bit. Set to 0 to use the channel 1
D2
TSRC1
0
external temperature sensor as the source of the temperature parameter for
V GATE1 calculations. Set to 1 to use the internal temperature sensor.
D[1:0]
APCSRC1[1:0]
00
Channel 1 APC parameter select bits. Set APCSRC1[1:0] to select the data
source for V GATE1 calculations. See Table 13c.
X = Don’t care.
*Write only.
______________________________________________________________________________________
53
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX11014BGTM+T
IC RF MESFET AMP 48-TQFN-EP
MAX12000ETB+T
IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T
IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+
IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T
IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315
EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315
EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433#
EVAL KIT MAX1472
相关代理商/技术参数
MAX11008EVKIT+
功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1100CWG
制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1101
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA
MAX11014
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014_08
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM+
功能描述:特殊用途放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
MAX11014BGTM+T
功能描述:射频放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel